In Timer mode, you can set up a 7-day schedule to control the heating in this zone. You set up a ‘heating period’ to suit your needs, including start time, end time and temperature. At the start of the heating period, the Genius Hub system will activate the heating in the room. Once the room has reached the set temperature, the system will maintain the temperature for the duration set.
...
The main difference between Timer mode in Radiator, Underfloor or Electric heating zones heating or Hot Water Temperature zones compared with On/Off zones is that you can set a temperature for these types of zone. In On/Off zones you can only set periods where the heating is on or off.
...
If you wish to view a day's schedule in more detail, click on the day you wish to view. This will load the details of the heating schedule including the default temperature and a list of the heating periods.
| Demonstration |
|---|
|
| Anchor | ||||
|---|---|---|---|---|
|
Adding a Timer period
With the Genius Hub system you can set as many heating periods as you require throughout the day.
| Info |
|---|
Each timer period must be a minimum of 5 minutes, however there are no other limits on the number of periods you can create. |
| Demonstration |
|---|
|
To add a timer period for a radiator or TPI heating zone:
- From the My House page, click on the zone you wish to view.
- Change the zone to Timer mode.
- Click on the first day to have a schedule added.
- Click the floating add heating period button found at the bottom-right of the page.
- To select the temperate, drag the slider to the correct temperature, then click Set.
Select when the heating period should begin, by first clicking on the hour the heating period will begin.
Next click on the minutes the heating period should begin, followed by Set.
Info If you want to change the hours the heating period starts at, click on the hours at the selected time.
- Select when the heating period should finish.
- Click OK.
...
| Anchor | ||||
|---|---|---|---|---|
|
| Demonstration |
|---|
|
If your schedule changes or the temperature in a room is not right for you, it is easy to change a Timer period.
To change a Timer period for a radiator, TPI or On/Off zone:
- From the My House page, click on the zone you wish to edit.
- Ensure the zone is in Timer mode.
- Click on the day you want to change the schedule of.
- Click on the Timer period you want to change.
- Click on the relevant option you want to change, e.g. the end time.
- Change the option to its new setting.
- Click OK.
...
To remove a Timer period for a radiator, TPI or On/Off zone:
- From the My House page, click on the zone you wish to edit.
- Ensure the zone is in Timer mode.
- Click on the day you want to change the schedule of.
- Next to the Timer period you no longer want, click on the 'Bin' icon.
- In the confirmation dialog, click 'Delete'.
...
For those times of day which you do not want the heating on high, you can set a default temperature, so that the room doesn't cool down too far, leaving you to return to a cold house or causing the room to take a long time to heat up again. As standard the system will use the Off setting for the default temperature, so a Radiator room will go into frost protect mode and the other room types will stay off.
The default temperature can be set for each day of each zone. To do this for radiator and TPI heating zones:
- From the My House page, click on the zone you wish to edit.
- Ensure the zone is in Timer mode.
- Click on the day which you want to change the default temperature.
- Click on the Default temperature entry at the top of the list of heating periods.
- Change the default temperature and click Set.
| Info |
|---|
Default temperatures are especially important with underfloor heating which can take a number of hours to reach the desired temperature. The reason for this is because if the floor gets too cold then it takes a very long time to warm up such as large mass, compared with a metal radiator. It is recommended that a default temperature of no less than 4°C below the normal heating temperature is selected. We also recommend you use Pre-Heat for Underfloor Heating zones. |
There is no configurable Default setting for On/Off zones. The zones are off by default and the Timer periods are always On periods.
| Anchor | ||||
|---|---|---|---|---|
|
| Demonstration |
|---|
|
Once you have set up the schedule for one day, it is easy to copy the schedule to another day. This can be very useful if you have a regular schedule, such as if you work regular hours on a number of days in the week.
...
| Anchor | ||||
|---|---|---|---|---|
|
| Demonstration |
|---|
|
After setting up the schedule for one zone, you may find it easier to copy the schedule from this zone to another one and adjust it. This is often the case if you have multiple bedrooms in the property for example.
...
- From the My House page, click on the zone you wish to copy the schedule from.
- Ensure the zone is in Timer mode.
- Click on the zone sub-menu and click 'Copy Schedule'.
- Select the zones you want to copy this rooms schedule to
- Click 'Copy'.
| Info |
|---|
|
| Note |
|---|
There is no way to recover a schedule once it is overwritten, so ensure you select the right zone(s). |
...
If your schedule has changed significantly, it may be easier to clear all the schedule for all of the zone and start again by adding new Timer periods.
| Demonstration |
|---|
|
To delete the entire schedule for a zone:
...
If you want to enable Pre-heating, please see the the 'Setup pages' chapter.
...
| bgColor | #ccc |
|---|---|
| borderStyle | none |
Related Information:
...
chapter.