Page Comparison

...

Setting up Footprint mode

Anchor
QuickActions QuickActions

Quick Actions

In Footprint mode there are three new settings to select between based on how you want Footprint mode to work in this zone. They are:

• Comfort: The zone will heat both reactively and predictively. The Genius Hub will use occupancy to heat the zone before you arrive and it will bridge any gaps for short periods of time that the zone was not used. If the zone was used at a particular time in the past 2 weeks it will be heated for the same time this week. The zone will also control to the active temperature if triggers are detected for more than the start after time if it did not expect you to be there, and it will turn off after the Stop after time of not sensing anyone in the room.
• Eco: The zone will heat both reactively and predictively. The Genius Hub will use occupancy information to heat the zone when you normally use the zone. If the zone was used at a particular time in the past 2 weeks it will be heated for the same time this week. The zone will also control to the active temperature if triggers are detected for more than the start after time if it did not expect you to be there, and it will turn off after the Stop after time of not sensing anyone in the room.
• Super-Eco: The zone will only heat reactively. The zone will also control to the active temperature if triggers are detected for more than the start after time if it did not expect you to be there, and it will turn off after the Stop after time of not sensing anyone in the room.
  Image Added

Zone Sub-Menu

Anchor
FootprintOptions FootprintOptions

Footprint Options

There are five options unique to footprint mode, which should be configured before you use Footprint mode

...

• Starts from: This is the time which the zone will stop responding to occupancy and is normally set for roughly the same time the when the last people go to bed. The default setting for the Starts from time  is: 23:00
• Ends at: This is the time when the zone starts reacting to occupancy again and is normally set for when the people get up in the morning. The default setting for the Starts from time  is: 06:00

Zone Setup

Other settings you may need to adjust prior to using Footprint mode are in the Zone Setup page. This can be accessed by:

1. Go to the room you want to setup for Footprint mode.
2. Click on the zone sub-menu
3. Click on 'Zone Setup'
   Image Removed

The relevant settings you may want to adjust are under the header 'Zone reactivity settings' and Pre-heat. For more information see the Setup Pages chapter.

Advanced Options

Anchor
CopyTimer CopyTimer

Copy to Timer

As the automatically created schedule is based on when people actually use the room rather than when it is thought people use the room the schedule can be more accurate than a manually created schedule in Timer mode. If you want to use the automatically created schedule in Timer mode, you can copy it by:

...

1. Go to the room you want to copy the schedule between modes
2. Click on the zone sub-menu
3. Click on 'Copy to Timer'

Anchor
CopyOptions CopyOptions

Copy Options

If you use Footprint mode in similar rooms you may want to use the same settings set up in 'Footprint Options'. You can copy the options between zones which can be put into Footprint mode by:

...

1. Go to the room you want to copy the Footprint Options from
2. Click on the zone sub-menu
3. Click on 'Copy Options'
4. Select the rooms to copy the options to
   

Quick Actions

In Footprint mode there are three new settings to select between based on how you want Footprint mode to work in this zone. They are:

• Comfort: The zone will heat both reactively and predictively. The Genius Hub will use occupancy to heat the zone before you arrive and it will bridge any gaps for short periods of time that the zone was not used. If the zone was used at a particular time in the past 2 weeks it will be heated for the same time this week. The zone will also control to the active temperature if triggers are detected for more than the start after time if it did not expect you to be there, and it will turn off after the Stop after time of not sensing anyone in the room.
• Eco: The zone will heat both reactively and predictively. The Genius Hub will use occupancy information to heat the zone when you normally use the zone. If the zone was used at a particular time in the past 2 weeks it will be heated for the same time this week. The zone will also control to the active temperature if triggers are detected for more than the start after time if it did not expect you to be there, and it will turn off after the Stop after time of not sensing anyone in the room.
• Super-Eco: The zone will only heat reactively. The zone will also control to the active temperature if triggers are detected for more than the start after time if it did not expect you to be there, and it will turn off after the Stop after time of not sensing anyone in the room.
  Image Removed

...

Anchor
ZoneSetup ZoneSetup

Zone Setup

Other settings you may need to adjust prior to using Footprint mode are in the Zone Setup page. This can be accessed by:

1. Go to the room you want to setup for Footprint mode.
2. Click on the zone sub-menu
3. Click on 'Zone Setup'
   Image Added

The relevant settings you may want to adjust are under the header 'Zone reactivity settings' and Pre-heat. For more information see the Setup Pages chapter.