Page Comparison

...

If the Override you have setup no longer suits your needs, you can edit the time and temperature of the Ovveride Override by:

1. From the My House page, clicking on the zone you have Overridden.
2. Click on either the time or temperature to change the setting.
3. The Override will update with the new setting.

...

For more information on setting up the manual Override, see the Zone Setup Pages chapter. check_meYou have different levels of override control possible, based on the device you are adjusting

To set an override from a device:

• On the Room Thermostat (DA-WRT-C) you can set the temperature of the override from the device. To override a zone from the thermostat:
  1. Press the up or down button until the desired temperature is reached. The zone will now override to the set temperature for the duration set on the app. If you stop at this point the system will use the override duration set on the app for this zone.
  2. If you wish to set the duration of the override, press the top button once for each hour you would like the override to last for. The zone will now override to the temperature and duration set on the thermostat. check_me
  <image of DA-WRT-C, buttons highlighted>
• On the Room Thermostat (DA-WRT-B) you can set the temperature of the override from the device. To override a zone from the thermostat:
  1. Rotate the dial until the desired temperature is reached. The zone will override to the set temperature for the duration set on the app.
  <image of DA-WRT-B, dial highlighted>
• On a Radiator Valve (DA-WRV-C, DA-WRV-B, or DA-WRV-A) you can set the temperature of the override from the device. To override a zone from the Radiator Valve:
  1. Press the up or down button until the desired temperature is reached. The zone will override to the set temperature for the duration set on the app.
• <image of DA-WRV-C, buttons highlighted>
• On the Single Channel Receiver (HO-SCR-C) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Press the On (top) button. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. Press the Off (middle) button. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of HO-SCR-C, buttons highlighted>
• 1. , and override to the last used override temperature/setting.
• On the Dual Channel Receiver (HO-DCR-C) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Check the door panel to see which of the white buttons relates to the zone you have chosen to override.
  2. Press both the correct white button and the green button at the same time. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. Check the door panel to see which of the white buttons relates to the zone you have chosen to override.
  2. Press both the correct white button and the red button at the same time. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of HO-CCR-C, door open, white & green buttons highlighted>
  1. , and override to the last used override temperature/setting.
• On the Electric Switch (HO-ESW-D) you can trigger an override from the device. To override a zone ON from the receiver unitElectric Switch:
  1. Press the button at the bottom left right hand corner of the receiver unit. The system will use the override duration and override temperature set on the app for this zone.
• <image of HO-ESW-D, buttons highlighted>
• 1. , and override to the last used override temperature/setting.
• On the Smart Plug (PH-PLG-C or PO-PLG-B) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. When the plug is off, press the button in the middle of the plug. The system will use the override duration and override temperature set on the app for this zone.
  To override a
  1. zone
  OFF from the receiver unit:
  1. When the plug is on, press the button in the middle of the plug. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of PH-PLG-C, button highlighted> check_me - all of above

...

• 1. , and override to the last used override temperature/setting.

...

If you have a device in the My House, such as a Receiver unit controlling your heating or a Thermostat reporting the temperature to My House this can be used to affect all of your Radiator and Underfloor rooms with one manual override. 

• For a Single or Dual Channel Receiver you can press the respective on button (as detailed above) and all of your Radiator and Underfloor rooms will override to the temperature and duration set in My House.
• For a Thermostat you can adjust the temperature (as detailed above) and all of your Radiator and Underfloor rooms will override to the selected temperature on the device and to the duration set in My House.

...

You only need to adjust one device in the zone. So if you have 2 Radiator Valves in the same room the system will take the override from one device and relay this new information to all of the devices in the room.