Page Comparison

...

1. From the My House page, click on the zone you wish to Override.
2. Change the mode to Override.
3. Select the temperature you want to Override the zone to. This can be up or down, and so can be used to bring the heating on at a different time of day or to turn it off earlier than usual.
4. Select the duration of the Override. 
5. The Override will start immediately.
   <image of override active, with temp and time set>

For an On/Off type of zone, you can only select the duration of the override. check_me

To check how long is left of the override:

...

In many of your zones the devices for that zone will have physical controls you can use to adjust the heating, such as the buttons on a Radiator Valve. Based on the settings you have chosen for in that Zone's Setup page, you may be able to set an Override without having to use the app. 

For more information on setting up the manual Override, see the Zone Setup chapter. check_me

You have different levels of override control possible, based on the device you are adjusting:

• On the Room Thermostat (DA-WRT-C) you can set the temperature of the override from the device. To override a zone from the thermostat:
  1. Press the up or down button until the desired temperature is reached. The zone will now override to the set temperature for the duration set on the app. If you stop at this point the system will use the override duration set on the app for this zone.
  2. If you wish to set the duration of the override, press the top button once for each hour you would like the override to last for. The zone will now override to the temperature and duration set on the thermostat. check_me
• <image of DA-WRT-C, buttons highlighted>

• On the Room Thermostat (DA-WRT-B) you can set the temperature of the override from the device. To override a zone from the thermostat:
  1. Rotate the dial until the desired temperature is reached. The zone will override to the set temperature for the duration set on the app.
• <image of DA-WRT-B, dial highlighted>

• On a Radiator Valve (DA-WRV-C, DA-WRV-B, or DA-WRV-A) you can set the temperature of the override from the device. To override a zone from the Radiator Valve:
  1. Press the up or down button until the desired temperature is reached. The zone will override to the set temperature for the duration set on the app.
• <image of DA-WRV-C, buttons highlighted>

• On the Single Channel Receiver (HO-SCR-C) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Press the On (top) button. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. Press the Off (middle) button. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of HO-SCR-C, buttons highlighted>

• On the Dual Channel Receiver (HO-DCR-C) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Check the door panel to see which of the white buttons relates to the zone you have chosen to override.
  2. Press both the correct white button and the green button at the same time. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. Check the door panel to see which of the white buttons relates to the zone you have chosen to override.
  2. Press both the correct white button and the red button at the same time. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of HO-CCR-C, door open, white & green buttons highlighted>

• On the Electric Switch (HO-ESW-D) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Press the button at the bottom left hand corner of the receiver unit. The system will use the override duration and override temperature set on the app for this zone.
• <image of HO-ESW-D, buttons highlighted>

• On the Smart Plug (PH-PLG-C or PO-PLG-B) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. When the plug is off, press the button in the middle of the plug. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. When the plug is on, press the button in the middle of the plug. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of PH-PLG-C, button highlighted> check_me - all of above

If you have a device in the My House, such as a Receiver unit controlling your heating or a Thermostat reporting the temperature to My House this can be used to affect all of your Radiator and Underfloor rooms with one manual override. 

• For a Single or Dual Channel Receiver you can press the respective on button (as detailed above) and all of your Radiator and Underfloor rooms will override to the temperature and duration set in My House.
• For a Thermostat you can adjust the temperature (as detailed above) and all of your Radiator and Underfloor rooms will override to the selected temperature on the device and to the duration set in My House.